Kasa Smart Switches
I have multiple locations where one HS200 switch is installed next to another one. The wall plate that comes with the switch is single gang. I have tried the usual Decora screwless 2-gang wall plate b
0Helpful
187Views
Ihavr the hs200 installed in my bedroom. It works great, but has an led ring indicator when the light is off. Is there a way to turn that off? Or switch it so the indicator is only on when the light i
0Helpful
475Views
The most frequent questions I have seen are related to 3-Way configurations. So here is a Tutorial that I hope will answer most questions, especially when it comes to installation. What is a 3-way (or
By
Bethel.8009
· Latest post 2021-08-18 14:41:00
by rickneworleans
0Helpful
103Views
This is a really common issue, especially when trying to install multiple Smart Switches into a relatively shallow switch box and worst case when you have a triple gang box to accommodate (with all th
By
Bethel.8009
· Latest post 2021-07-05 06:38:52
by AnnaGabler
0Helpful
47Views
I am trying to install the HS200 in my home. However the location where I am installing it at is at the end of a 15A breaker. In other words there are other lights on this line. I can't see the ground
By
andrewm659
· Latest post 2021-04-28 10:11:00
by DerekGroff
0Helpful
60Views
Wiring instructions OK until told to connect Load and Line wires to switch. Identified wall Load and Line wires, but could not find anything identifying which are the corresponding two poles on the sw
0Helpful
25Views
Added my new Deco WiFi and all my TP-Link Kasa switches and plugs don't work. How do I reset them to the new WiFi?
By
PhotoGuyMike
· Latest post 2020-11-05 20:10:59
by Carl
0Helpful
17Views
Does TP-Link have any plans in the near future to release a 3-way dimmer switch? I have the HS200 and HS220. I would love it if the HS220 had the 3Way capability.
0Helpful
1634Views
Switch was working fine Is with Alexa and kasa. It the then stopped working on Alexa but stillworked in Kasa. Removed it from Kasa and tried reinstalling. When rest I get flashing green then solid Gre
By
Brett_Auburn
· Latest post 2021-09-17 04:30:30
by JohnD84
0Helpful
18Views
I just installed a spare HS200 I had sitting around. While connecting it to my account it indicated that a firmware update was required. When I tried updating the firmware at that time, the app indica
By
phxDiablo
· Latest post 2021-09-15 08:13:48
by Solla-topee
0Helpful
16Views
I'm baffled. I want to install a Kasa HS200 in place of a mechanical switch to operate a ceiling light. The existing installation has 4 wires - black, red, white and bare copper ground. The machanical
By
Engineer_Dan
· Latest post 2021-09-10 01:37:47
by Kiwidg
0Helpful
163Views
Purchased 6 HS210 switches. 2 work properly 4 do not on simple 3 way lighting circuits. The 4 that do not work properly require two button tap in app to change status of physical switch, app status ch
By
Otrip
0Helpful
7Views
Is Kasa working on expanding its product line to include a 2 or 3 gang (double or triple) wall switch? I see that 2 gang smart wall switches are offered by some other companies but I like the Kasa env
By
SwitchedOnSteve
· Latest post 2021-09-09 17:54:24
by kontractor13
0Helpful
29Views
My HS220 is in my bathroom off of my bedroom. I want to schedule it so between the hours of 10 PM and 6 AM, if I turn the light on, it will be at a specific brightness (but only if the light is on). E
0Helpful
72Views
Hi, we have approximately 20 Kasa Smart Switches in our house. We love them but I've noticed some weird things recently. About three weeks ago, I noticed that all the lights would randomly turn on for
0Helpful
12Views
I have found that my dimmer switches, all of the 3 i have installed, cause my LED bulbs to flicker ONCE as they ramp up to 100%. if i set them to 98%, they do not. i am positive that it is not a wirin
0Helpful
23Views
When turning on the HS220 dimmer, it goes from dim to bright and then goes off for a fraction of a second and then back on to full. This happens with two fixtures, a chandelier with 5 dimmable LED bul
0Helpful
30Views
I have a 2 switch panel in which I want to replace only one switch with the HS200. From left to right: Switch 1: Controls the outside lights and it is the only switch that controls the lights Switch 2
0Helpful
20Views
I wired up my shiny new KS220M motion sensor switch and played with the motion sensitivity. I have the motion sensitivity set to the "far range" (25', maximum sensitivity). The light is set to turn on
By
Paul92029
· Latest post 2021-09-07 11:42:59
by Solla-topee
0Helpful
21Views
Hi. I have 4-5 HS220v1 throughout my house which work great. I just bought a new batch and it seems that the V2 versions (firmware 1.0.3) keep restarting themselves every 30 seconds. I have even tried
0Helpful
84Views