Hi All,

 

This thread will be updated once there is a new firmware released in the future, welcome to subscribe.

 

To avoid bothering you with unrelated messages, this thread will not allow replying from now on. 

Any further questions/feedback on the new firmware, please feel free to start a new thread from HERE.

 

Thank you so much for your great cooperation and understanding!

 

 

----------------------------------------- ------------------------------------------------------------------- ----------------------------------------

---------------- *Firmware v1.1.1 for ER605 and ER7206* ----------------

----------------------------------------- ------------------------------------------------------------------- ----------------------------------------

 

 The firmware v1.1.1 has been released for both ER605 and ER7206 by August 9, 2021.

 

Attention: 

It is recommended to reboot the ER605 before upgrading to the firmware v1.1.1, otherwise, the bugs in the older firmware may cause the upgrade to fail. Related discussions can be found here. Thank you for your attention!

 

Published Date: 2021-07-29, 2021-08-06

Release Notes:
 

New Feature/Enhancement:

 

• New features in both Controller mode and Standalone mode:

 

1. Add support for Dual Image feature and optimize the Flash design to improve stability and reliability (For ER7206 only).

Note: this feature is similar to the Dual Image feature on the switch, the only difference is that we cannot manually configure the backup image. The ER7206 will automatically activate the backup image once it fails to start up with the startup image.

2. Add Emergency mode to recovery the firmware, please refer to FAQ3062.

3. Add support for IPv6.

4. Add support for Daylight Saving Time (DST).

5. Optimize the mechanism of aging UPnP entries (For ER7206 only).

6. Optimize the priority of One-to-One NAT and IPsec tunnels.

 

• 7. New features in Controller mode:

7.1 PPTP/L2TP VPN can be selected as the Interface for static route and policy routing.

7.2 Add support to customize the firewall parameters.

7.3 Routing table, VPN, DDNS and Port forwarding status can be displayed on the Insight page.

7.4 Optimize the export of OpenVPN certificate.

 

• 8. New features in Standalone mode:

8.1 Multi networks are supported.

8.2 LAN-to-LAN ACL are added to manage the behavior between networks, refer to FAQ3061 for Configuration Guide.

 

Bug Fixed:

1. Fix the bug that Omada Gateway cannot be adopted after upgrading the firmware.

2. Fix the bug that the device account was reset after multiple configurations.

3. Fix the bug that TTL of the packets is reduced by 2 after forwarding.

4. Fix the bug that the existing sessions may not be switched to the backup WAN when performing the link backup.

5. Decouple some configurations of WAN and LAN.

6. Fix the bug that Virtual Server, One-to-One NAT and NAT Loopback failed.

7. Fix the bug that Speed Test failed in some circumstances.

 

Upgrade Notes:

1. Your device’s configuration won’t be lost after upgrading.

2. This firmware is applied to the Omada APP of version 3.0.x or above.

3. This firmware is fully adapted to the Omada SDN Controller 4.3.5 or above.

Direct Download:

ER605(UN)_v1_1.1.1 Build 20210723 --> For ER605 (aka TL-R605) v1.0 and v1.6.

ER7206(UN)_v1_1.1.1 Build 20210723 --> For ER7206 (aka TL-ER7206) v1.0 and v1.6.

 

For more information about ER605 and ER7206, please check the download link below.

https://www.tp-link.com/en/support/download/er605/#Firmware

https://www.tp-link.com/en/support/download/er7206/#Firmware

 

*Any further questions/feedback on the new firmware above, please feel free to start a new thread from HERE.

 

----------------------------------------- ------------------------------------------------------------------- ----------------------------------------

---------------- *Firmware v1.0.1 for ER605 and ER7206* ----------------

----------------------------------------- ------------------------------------------------------------------- ----------------------------------------

 

Published Date: 2021-03-03

ER605(UN)_V1_20210113 --> For ER605 (aka TL-R605) v1.0 and v1.6.

ER7206(UN)_V1_20210113 --> For ER7206 (aka TL-ER7206) v1.0 and v1.6.

 

New Feature/Enhancement:

1. Support to configure the L2TP VPN Server and IPsec site on the same WAN port.

2. Change the detection mechanism of the “Block Ping of Death” function in the firewall, remove the packet limit of fewer than 64 Bytes. Discussed HERE.

3. Optimize the Online Detection and DNS proxy mechanisms to improve the network stability for scenarios where the front-end device has a Disconnection Alert function.

4. Optimize for scenarios where the Omada SDN Controller is accessed via the cloud when Portal is enabled.

5. Improve the compatibility of IKEv2 VPN, and the stability of L2TP over IPsec VPN.

6. Improve the network stability when the static IP address is changed in multi-WAN mode.

 

Bug Fixed:

1. Fix the bug that the DHCP Server may down under special circumstances. Discussed HERE.

2. Fix the bug that the WAN connection may down when multi-network and VPN are configured.

3. Fix the bug that the router doesn’t forward data for up to 2 minutes when the L2TP VPN Client is connected.

4. Fix the bug that the Omada SDN Controller alerts incompatible devices. Discussed HERE.

5. Fix the bug that CPU and memory usage data are not correctly displayed in the Statistics functions of the Omada SDN Controller. Discussed HERE.

6. Fix the bug that the router occasionally generates the wrong routing table for the DNS server.

 

For more information about the ER605(TL-R605), please check the download link below.

https://www.tp-link.com/en/support/download/tl-r605/#Firmware