@KevinCH out of interest how do you know it's now working? I am looking tomuse ethernet backhaul but have no idea how to tell it is functioning.

@KevinCH 

Hello,

Sorry to hear that the Deco P7 failed to build up the Ethernet backhaul. Please confirm some details and we can try to fix it together. 

1. What is the current network topology/diagram? How many Deco P7s do you have in total and how are they connected?

2. What is the model number of the gigabit switch, is it TL-SG1008? What if you remove the switch temporarily from the network and connect the Deco P7 together, will they be able to build up the Ethernet backhaul?

3. Try to reset the Deco P7 to factory defaults and reconfigure it from scratch, then confirm again if they can build up the Ethernet backhaul when adding the switch back into the network.

@atca You may confirm this by clicking the Internet icon on your Deco app (ensure it is the latest version)->tap the satellite Deco, then you will see the satellite Deco’s signal source. For more details, you may refer to the below FAQ:

https://www.tp-link.com/support/faq/1794/

Good day.

@TP-Link_Deco 

1. What is the current network topology/diagram? How many Deco P7s do you have in total and how are they connected? I have 5 P7s.  One of them is connected via ethernet backhaul and the rest of them are connected via wireless or via powerline.

2. What is the model number of the gigabit switch, is it TL-SG1008? It is TL-SG108. What if you remove the switch temporarily from the network and connect the Deco P7 together, will they be able to build up the Ethernet backhaul? I have not tried that yet because this network is located in a different house.  I will have to wait until I go back to that house in order to test this.  However, it's important for you to understand that I had an expensive D-Link 16-port switch and I removed that and purchased 2 of your TL-SG108 swtiches because your tech support blog says that D-Link switches prevent the ethernet backhaul from working correctly.  It appears that I wasted my money buying the 2 TL-SG108 switches...

3. Try to reset the Deco P7 to factory defaults and reconfigure it from scratch, then confirm again if they can build up the Ethernet backhaul when adding the switch back into the network. I really don't want to do this because it will take time to reconfigure everything.  Are you sure you can't solve this problem so that I don't have to erase the router's configuration?

@atca You may confirm this by clicking the Internet icon on your Deco app (ensure it is the latest version)->tap the satellite Deco, then you will see the satellite Deco’s signal source. For more details, you may refer to the below FAQ:

https://www.tp-link.com/support/faq/1794/

@KevinCH 

Hello, terribly sorry for all the inconvenience caused in this case, but don't worry that we will try our best to figure it out.

Can I confirm your network layout again?

Modem--->Main Deco P7 (Router mode)--->SG108--->2nd P7, all other P7s are connected wirelessly or via PLC backhaul

BTW, we will contact you via email to follow up your case, please check your email box and respond.

Thanks.

TP-Link_Deco wrote

@KevinCH 

 

Hello, terribly sorry for all the inconvenience caused in this case, but don't worry that we will try our best to figure it out.

 

Can I confirm your network layout again?

Modem--->Main Deco P7 (Router mode)--->SG108--->2nd P7, all other P7s are connected wirelessly or via PLC backhaul

 

BTW, we will contact you via email to follow up your case, please check your email box and respond.

 

Thanks.

@TP-Link_Deco 

Hi,

I have tried a couple of different configurations:

1.  the one you described above and

2. Modem-->sg108-->main deco and kitchen deco connected ethernet to the switch (not in series), with all other decor connected wirelessly or via powering

 unfortunately, both of the configurations I've described above produce the same results -  the kitchen p7 does not utilize the ethernet backhaul.

 please let me know if you have any ideas on how to improve the configuration. 

Thank you

@KevinCH 

I have the same issue with the same switch (TP-Link SG-108). These are unmanaged switches so there should be no loop back prevention feature (or at least a method to disable it). 

Has anyone heard of any fix?