Archer MR600(EU) V1 - BETA Firmware - Allowing selection of 4G+bands for Archer MR600 manually
This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.
Hi all,
Following the long thread on the same subject discssing the BETA FW, as I said I would, TPLink have given me permission to share the FW download llink.
From TPLink - We recently released a beta firmware for Archer MR600(EU) V1 which can allow us to select 4G+bands for Archer MR600 manually.
https://static.tp-link.com/2020/202004/20200420/Archer_MR600v1_1.1.0_0.9.1_[200417-rel75138]_up_boot_2020-04-20_08.44.31.zip
For Archer MR600, if you want to use its 4G+network, your SIM card should support the CA bands group Archer MR400 supports. Please check the attached picture and check if your SIM card supports the band groups on the list or not.
They asked me to state that, this BETA FW is for the Archer MR600(EU) V1 ONLY!
Neither TPLink nor me take any respnsbility if you flash a none-EU router.
- Copy Link
- Subscribe
- Bookmark
- Report Inappropriate Content
am getting error pls help me
- Copy Link
- Report Inappropriate Content
your hardware version is V2 but you are trying to upload V1 hardware firmware? please check.
- Copy Link
- Report Inappropriate Content
How to downgrade it to v1 ?
- Copy Link
- Report Inappropriate Content
It is possible only if you buy older router MR600V1
You already have better device and firmware, Why do you want v1 ?
- Copy Link
- Report Inappropriate Content
Its been a year i have been using the External LDPA's it was working great. from past month i see decline in speed and signal. Now its like almost gone. I am confused whether antenna's degrade by time. Should i need to buy new pair again or is it Tower issue which am pointing to. Any one experienced this?
- Copy Link
- Report Inappropriate Content
Can some one please explain me this
if i run speed test in Firmare page am getting this
same thing if i run in browser am getting this
Which one is true. Am truely confused as to which one is correct. i tried connecting laptop through LAN and ran test but nothing goes beyond 10mpbs but in firmware it always clock more then 25mpbs.
- Copy Link
- Report Inappropriate Content
New firmware: 1.3.0 0.9.1 v0001.0 Build 210608 RC.66100n
Band selection is not supported. :(
- Copy Link
- Report Inappropriate Content
No band selection would not be a problem, if it would do it right automatically!
THIS is the problem:
-----------------------------------------
Open Source Code For Programmers (GPL)
Please note: The products of TP-Link partly contain software code developed by third parties, including software code subject to the GNU General Public Licence (“GPL“), Version 1/Version 2/Version 3 or GNU Lesser General Public License ("LGPL"). You may use the respective software condition to following the GPL licence terms.
You can review, print and download the respective GPL licence terms here. You receive the GPL source codes of the respective software used in TP-Link products for direct download and further information, including a list of TP-Link software that contain GPL software code under GPL Code Center.
The respective programs are distributed WITHOUT ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or F|TNESS FOR A PARTICULAR PURPOSE. See the respective GNU General Public License for more details.
-----------------------------------------
Does it mean it is good for nothing?... >:( Please explain!
Uh?... They don't accept what they write!!! ROTFL!!! :D
"The following sensitive language has been used which goes against the rules of the SMB Community: "F|TNESS". Please enter again. "
- Copy Link
- Report Inappropriate Content
Is that means we are stuck with this beta firmware? It seems no final firmware will have band selection. Haizz..
- Copy Link
- Report Inappropriate Content
I need a daily data limit in MR 600... Is it possible ? I can see only the monthly limit.
- Copy Link
- Report Inappropriate Content
Information
Helpful: 0
Views: 549
Replies: 0
Voters 9
