Archer MR600(EU) V1 - BETA Firmware - Allowing selection of 4G+bands for Archer MR600 manually
This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.
Hi all,
Following the long thread on the same subject discssing the BETA FW, as I said I would, TPLink have given me permission to share the FW download llink.
From TPLink - We recently released a beta firmware for Archer MR600(EU) V1 which can allow us to select 4G+bands for Archer MR600 manually.
https://static.tp-link.com/2020/202004/20200420/Archer_MR600v1_1.1.0_0.9.1_[200417-rel75138]_up_boot_2020-04-20_08.44.31.zip
For Archer MR600, if you want to use its 4G+network, your SIM card should support the CA bands group Archer MR400 supports. Please check the attached picture and check if your SIM card supports the band groups on the list or not.
They asked me to state that, this BETA FW is for the Archer MR600(EU) V1 ONLY!
Neither TPLink nor me take any respnsbility if you flash a none-EU router.
- Copy Link
- Subscribe
- Bookmark
- Report Inappropriate Content
I updated to the latest BETA firmware. I don't have a problem, though I don't automatically restart the router. In the evening, I usually turn off the main power switch so that I don’t consume power. It has a band selection feature, but I can't test it. Only B20 800 MHz available, bandwidth: 20 MHz.
https://www.speedtest.net/result/10670767601.png
- Copy Link
- Report Inappropriate Content
Hi all,
as first thanks for accepting me in this community.
I've just bought a brand new MR600, and I'd like to test the beta FW. Can I roll back to the original FW in case of problem ?
Thanks in advance and happy new year !
Have a good day,
Felice
- Copy Link
- Report Inappropriate Content
hi nice post i am also fedup with mr600 kindly provide link to buy Huawei B525s-65a and also provide link for custom firemware
- Copy Link
- Report Inappropriate Content
Happy New Year 2021.
Thanks for your reply.. kindly provide the link to buy Huawei router as I couldn't get online shopping in India
- Copy Link
- Report Inappropriate Content
@Satheskumar Hows your Huawei? Which particular model did you get? MR600 is hopeless.
- Copy Link
- Report Inappropriate Content
Hi any of you facing issue with globalconnect when connected to TPLINK. Recently my company switched from cisco annyconnect to Global connect for VPN. from then this problem have started up where when ever i connect to TPLINK, it gets connected but no internet, sites dont load. when i disconnect it all starts working again. I connected to other router like DLINK and even have connected to IPhone hotspot, it works perfectly. I googled but i couldn't find any solution. If any one have come across similar problem please let me know
- Copy Link
- Report Inappropriate Content
Hello,
Yes, you can roll back to the official firmware if you don't want to use the beta version on the MR600.
- Copy Link
- Report Inappropriate Content
Hi, may I know who is your SIM card provider? Is there a correct IP address when you cannot open any sites? Please go to Advanced>>Network>>LAN settings>>change DNS address to be 8.8.8.8/8.8.4.4, then check again.
- Copy Link
- Report Inappropriate Content
@Kevin_Z My sim card is Airtel, I am able to access internet when not connected to VPN, but when i connect to VPN (globalprotect) Though it gets connects sucessfully, later when i open browsers none of the site loads, its keep spinning and wont load. I will try changing the DNS address and see once. Thanks
- Copy Link
- Report Inappropriate Content
- Copy Link
- Report Inappropriate Content
Information
Helpful: 0
Views: 734
Replies: 0
Voters 9
